ARC Racing

3/8-24 Left hand thread male tie rod end.

5/16-24 Right hand thread male tie rod end.

5/16-24 Left hand thread male tie rod end.

8 foot Throttle Cable Jacket

16ft 3/16" Hydraulic Brake Line

For Jr Dragsters and Lawnmower Racers (4) 1/2-20 x1-1/2" Long Bolts (4) Flanged Nuts

 .010 Valve Spring Shim

 .005 Valve Spring Shim

6615 Drag PVL Flywheel. For use with the Fits Briggs and Stratton digital PVL ignition system on the Fits Honda GX200/196cc Clone, Tillotson 196/212/225/228/236 engines. Finnless Flywheel designed...

Honda Gx160 UT2 piston. Use with DJ-2190 rings.

Oil Drain plug with washer. Fits GX160 GX200 Clone BSP and Predator 212 engines.

Thick rubber air box to carb gasket for the GX390 and Predator 301/420cc engines

(2) Chromoly Cut to Length Push Rod for Honda GX390 *SOLD AS A PAIR* When shortening the columns more than 3/8" it will be necessary to re-size the hole with a .125" reamer to a min. depth of .250"...

*Depending on availability, pushrods may be black anodized or uncoated. Chromoly Cut to Length Push Rod for Honda GX390 *SOLD INDIVIDUALLY* When shortening the columns more than 3/8" it will be...

PVL ignition coil 555681 has a 12,000 RPM limit! For use on Animal, World Formula, and with the ARC PVL billet flywheels. You must use the specific PVL flywheel with this coil  

ARC Top Plate/Throttle Control Linkage Assembly for the Fits Honda GX270, GX340, GX390 and Predator 301cc and 420cc Engines. This Part is made with quality components and the same attention to detail...

The new 6695 billet flywheel from ARC Racing for the Predator 212 NON-Hemi has an ultra low drag fin design that will greatly reduce air drag on your racing engine, while still moving enough air for...

The new 6689 billet flywheel from ARC Racing has an ultra low drag fin design that will greatly reduce air drag on your AKRA racing engine, while still moving enough air for cooling. Less air drag on...

2 Pack of Stock Appearing Valve Springs for the Briggs Animal

2 Pack of Heavy Duty Valve Springs for Honda GX240, GX270, GX340, & GX390.Approx 50 lbs at 1.125 installed height, 42lbs at 1.2, with 110 lb open pressure (.375 lift).

2 Pack of 22Lb Valve Springs.These springs are recommended for use with the stock retainers. 22lbs @ .850"

For Modified BSP, Clone, GX200, Predator 212, and Yamaha F200. 36lbs at .850 installed height and coil bind at .450. Requires part number ARC_DJ-1046 retainer and keeper kit. May require head...

2 Pack of 26Lb "White" Springs. Use as intake spring when using stock intake valve and ARC DJ-1046 Spring retainer. Use as Heavy spring for intake and exhaust when using our stainless (DJ-1121,22 and...

*Depending on availability, pushrods may be black anodized or uncoated. *SOLD INDIVIDUALLY* .187 Diameter chromoly stock length used in Fits Honda GX200, 196cc Clone, 1st and 3rd generation Harbor...

Predator MLS head gasket .018" thick by 72mm(2.835") bore. MLS stands Multi Layer Steel. MLS head gaskets feature embossed stainless steel Viton coated outer layers for excellent sealing and...

Tillotson 4_Cycle Gas Carburetor.790 Venturi X 1.005 Throttle Bore.790 Bore Gasoline Only

1.3 ratio GX200 / Clone Billet Steel Rocker SetReplaces the stock rockers with 1.3:1 ratio billet steel rocker arms, heavy duty billet steel rocker studs, lash caps, rocker pivots, adjuster nuts, set...