NR RACING

"MoFlow-1 by BlackMarkit The new Moflow has been completely reworked to accept ""bigger"" valves, utilizing a 36mm intake valve and a 27mm exhaust. The valve spacing has been widened to safely...

"MoFlow-1 by BlackMarkitBillet Cylinder Head for Small Block GX160/GX200, and Clone Engines 32mm intake and 25mm exhaust Optimized flow and velocity 14cc combustion chamber Comes with 45lb springs,...

"GX270 28mm Flat Slide Gas Carb Kit Kit includes manifold/adapter, air filter, air filter adapter/velocity stack, hose, and clamps. (Note: this has a square slide carb, which is far superior to the...

"40mm OD x 34mm ID Manifold exclusively for Billet Moflow ""Bigger Valve"" Heads Wide bolt spacing 46mm intake - fits ""Bigger 36 x 27"" valve Moflow Spigot (hose) style 3"" long "

"35mm OD x 30mm ID Manifold exclusively for Billet Moflow ""Bigger Valve"" Heads Wide bolt spacing 46mm intake - fits ""Bigger 36 x 27"" valve Moflow Spigot (hose) style 3"" long "

"Mikuni 22mm Carb to GX200 Intake Manifold Also adapts GX390 and most flanged carbs. Available in Black, Red, Gold, or Blue. (Some colors may be higher in price, depending on availability...

Make Ur Own GX390 Exhaust KitCan't find a system to fit your application? Use this kit to fabricate your own system! This can be either clamped or welded together.1-1/8" (1.125") OD pipe with one end...

Make Ur Own Exhaust Kit - Karting - GX200Cant find a system to fit your application? Use this kit to fabricate your own system! Can be either clamped or welded together.1" OD pipe with one end flared...

Aftermarket Replacement Lifter for 13/15hp Chinese OHVs*Note: Sold individually. Clone lifters have a lot of variance in length and may be slightly longer than Genuine Honda lifters.

"Stamped 1.3 Ratio Genuine Yamaha Rocker Arms - Each Stronger and better design than the clone version of these rockers Use with 22lb springs and stock lift cams only. Price is for single rocker...

Honda Oil Drain Extension for GX240 to GX390 and 420cc PredatorChange oil without the mess! This Drainzit brand extension is easy to install, simple to use, and requires no engine modification. May...

Rubber Spark Plug BootNon-Resistor*Note: Color may vary from picture.

"22mm Round Slide Mikuni Gas Carburetor KitFits all GX160s, 200s, 6.5 Chinese OHVs, and Predators. Great for mini bikes.A low-cost way to add HP! Kit Includes: 22mm Mikuni Style Carb (Small...

"Extreme Duty Black Aluminum Retainer for Dual Springs & Split Keepers*Note: Retainers are sold individually; however, two are needed per motor.Keepers not included >keeper set...

Change oil without the mess! This Drainzit brand extension is easy to install, simple to use, and requires no engine modification. May be used on nearly all equipment powered by small engines:...

".045"" Fiber Gasket to Fit 90-92mm Bores Will fit most 420cc and up 13/15hp Chinese OHVs *Picture is for reference only. Color and style may vary."

Wiseco Spiral Lox Clips for .490 Pins - One Pair

"High Quality Cometic Fiber Head Gasket for 3.0"" (76mm) Bore Best sealing of all the head gaskets we sell! Fits 212 Predators, GX200s, and 6.5 Chinese OHVs with 3.0"" bores "

"High Quality Cometic Fiber Head Gasket for 2.815"" (72mm) Bore Best sealing of all the head gaskets we sell! Fits 212 Predators, GX200s, and 6.5 Chinese OHVs bored to 2.815"" (72mm). "

Quick-Set Degree Wheel KitThe arbor shaft slips over the PTO and uses a slip-clutch to provide quick and easy degree wheel operation on all 4-cycle engines. The 360 degree markings make Chinese OHV...

Carbon Fiber Catch Can (Tank) - Briggs LO-206 StyleOne 1/4" inlet, one 3/16" inlet (carb overflow), and one 5/16" outlet

Carbon Fiber Catch Can (Tank) - GX200/Clone StyleOne 1/4" Inlet and One 5/16" Outlet

BPR6EIX NGK Iridium Spark PlugSame heat range as the OEM plug, but with iridium tip for long life and high-compression applications.

#35 Chain, fits Bully Turbos for 1" shaftsAvailable in 14-20 Tooth*Manufacturer of driver may be Bully or other company, depending on availability.

"Adjustable Ignition Coil Bracket for GX200, 6.5 Clone, 212/224 PredatorFor use with our GX200 Hot CoilKit Includes Front and back adjustable bracket plates Bracket hardware Billet...

"High-Quality Large Aluminum Catch Can Choice of Colors: Red, Blue, Gold (Yellow), Silver, or Black Gloss Finish Tank Size: 6.25 x 3.25 x 3.25 Capacity: 750 ML Billet or TIG Welded T-6061...

"High-Quality Large Aluminum Catch Can Choice of Colors: Red, Blue, Gold (Yellow), Silver, or Black Gloss Finish Tank Size: 6.25 x 3.25 x 3.25 Capacity: 750 ML Billet or TIG Welded T-6061...

"High-Quality Large Aluminum Catch Can Choice of Colors: Red, Blue, Gold (Yellow), Silver, or Black Gloss Finish Tank Size: 6.25 x 3.25 x 3.25 Capacity: 750 ML Billet or TIG Welded T-6061...

"High-Quality Large Aluminum Catch Can Choice of Colors: Red, Blue, Gold (Yellow), Silver, or Black Gloss Finish Tank Size: 6.25 x 3.25 x 3.25 Capacity: 750 ML Billet or TIG Welded T-6061...

"High-Quality Large Aluminum Catch Can Choice of Colors: Red, Blue, Gold (Yellow), Silver, or Black Gloss Finish Tank Size: 6.25 x 3.25 x 3.25 Capacity: 750 ML Billet or TIG Welded T-6061...